Rigid PCB board is a conventional Printed Circuit Board. It cannot be bent or flexed.
A Rigid PCB board is one of the important components of electronics product manufacture. Almost every electronic product must be used PCB board, from small watches, and calculators to computers, electronic communication equipment, and even military weapon systems.
Single layer rigid PCB is the most basic PCB. Components are concentrated on one side and circuits are concentrated on the other side. Single layer PCB board has many strict restrictions on the design circuit (because there is only one side, the wiring can not cross and must go around the unique path), only the early circuits use this kind of board.
2-Layer Rigid PCB Board circuits on both sides of this board, to use both circuits, proper circuit connections must be made between the two sides. This “bridge” between circuits is called a via. The via hole is on the PCB board, filled with or coated with a metal hole, and it can be connected to the wires on both sides. Because the area of the dual panel is double that of the single panel, the dual panel solves the difficulty of wiring in a single panel (via conduction through the hole to the other side), which is more suitable for use in more complex circuits than a single panel.
4 Layer rigid PCB, 6 Layer rigid PCB, 8 Layer rigid PCB and more layers, we call them mulitlayer rigid PCB.
In order to increase the area that can be routed, multilayer rigid PCB boards use more single or double-sided wiring boards.
Usually, the number of layers is even, and the outermost two layers are included. Most of the motherboards are 4 layer to 8 layer structures.
Super-multi-layer boards have gradually become unused. Because the layers in the PCB are tightly integrated, it is generally not easy to see the actual number, but if you look closely at the motherboard, you can still see it.
O PCB rígido pode ser aplicado cada vez mais amplamente porque tem muitas vantagens exclusivas, conforme descrito abaixo.
For decades, the high density of rigid PCBs has grown as integrated circuits have become more integrated and installation technologies have advanced.
Through a series of inspections, tests, and aging tests, the rigid PCB circuit board can be reliably operated for a long period of time (usually 20 years).
For rigid PCB performance (electrical, physical, chemical, mechanical, etc.) requirements, PCB circuit board design can be achieved through design standardization, standardization, etc., with short time and high efficiency.
With modern management, we can carry out standardization, scale (quantity), automation and other production, and ensure the consistency of product quality.
Established a relatively complete test method, test standards, a variety of test equipment and instruments to detect and identify the qualification and service life of rigid PCB circuit board products.
Rigid PCB board products not only facilitate the standard assembly of various components, but also can be automated, large-scale mass production. At the same time, PCB circuit board and various component assembly parts can also be assembled to form larger parts and systems up to the complete machine.
Since rigid PCB products and various component assembly parts are produced with standardized design and scale, these components are also standardized. Therefore, once the system fails, it can be quickly, easily, and flexibly replaced, quickly recovering from the system’s work. Of course, you can also give more examples. For example, the system is miniaturized, lightweight, and the signal transmission speed is increased.
The main raw materials commonly used in rigid PCB are substrate, copper foil, PP, photosensitive material, solder mask and film.
Copper-clad laminate is a composite material made from wood pulp paper or glass fiber cloth as a reinforcing material that is impregnated with resin and then covered on one or both sides with copper foil. It undergoes a hot-pressing process. In the production of rigid PCB multilayer boards, this material is commonly referred to as the core board or CORE.
The copper foil serves as the cathode component of the electrolytic material, and is deposited onto a thin continuous metal layer on the rigid PCB substrate
Externamente, ele pode ser facilmente colado à camada isolante, que acomoda a camada protetora e é gravada para criar o padrão do circuito.
A espessura do cobre PCB rígido é normalmente categorizada em variantes de 1 onça (35 µm), 2 onças (70 µm) e 3 onças (105 µm).
PP is a thin insulation material used for rigid printed circuit boards. Prior to being laminated, PP is in the form of a prepreg, also known as pre-impregnated fiber. It is primarily utilized as the adhesive and insulating material for the inner conductive pattern of multilayer circuit boards.
Once the PP has been laminated, the semi-cured epoxy is forced out, begins to flow, and ultimately solidifies, creating a strong bond that joins the multilayer circuit boards together, resulting in a dependable insulating layer.
These materials are generally classified as either photoresist or photosensitive film, and within the industry they are further divided into wet and dry film categories
When exposed to certain wavelengths of light, wet-film coatings on rigid PCB copper clad laminates undergo a chemical transformation that alters their solubility in the developer (solvent).
Dry film is further categorized into positive and negative film, differentiated by their photodegradable and photopolymerizable properties. Both types are highly sensitive to ultraviolet rays
This is a typical liquid photosensitive material that has no compatibility with liquid solder. It undergoes a chemical transformation and solidifies under specific lighting conditions. There are various ink colors available, with green being the most frequently used color for solder mask.
| Item | Parâmetros técnicos | Especificação |
| Largura/espaço mínimo da linha do circuito | 3/2,7 mil | Espessura de cobre acabada H oz |
| Anel de almofada PCB rígido mínimo da Via | 3 milhões | Distância entre a borda do furo e a periferia do anel |
| Anel de almofada de PCB rígido mínimo de PTH | 5 milhões | Distância entre a borda do furo e a periferia do anel |
| PCB rígido mínimo por tamanho | 4 milhões | Espessura da placa < 1,2 mm |
| Espessura mínima de PCB rígida de dupla face | 0,2 mm | Espessura Final da Placa |
| Espessura mínima de PCB rígida de multicamadas | 0,4 mm | Espessura Final da Placa |
| Espessura máxima de PCB rígida | 8,0mm | Espessura Final da Placa |
| Dimensão máxima do PCB rígido | 609×609 milímetros | PCB de face única e dupla |
| Espaço entre a linha e a borda da placa | 10 milhões | Fresagem de Contorno |
| Camadas rígidas máximas de PCB | 30 camadas | |
| Cor rígida da máscara de solda PCB | Verde, preto, azul, vermelho, branco, amarelo, | |
| Cor rígida da serigrafia PCB | Branco, preto, amarelo | |
| Acabamento de superfície de PCB rígido | HASL,ENIG,ENEPIG,ImAg,ImTin,OSP, chapeamento de ouro duro | |
| Espessura máxima de cobre de acabamento | 6 onças | |
| Espessura dielétrica | 2,5 milhões | |
| Material rígido de PCB | FR-4, substrato de alumínio, Rogers4350C, poliimida | |
| Tecnologia Especial | HDI PCB, via in Pad PCB, PCB cego e enterrado |
Below is the basic production process of China Rigid PCB factory.
In order to increase rigid PCB assembly density, the vias on the double-sided circuit board of the PCB circuit board are getting smaller and smaller. Generally, double-sided PCB circuit boards are drilled with CNC tolling machines to ensure accuracy.
Plating hole process, also known as metallized hole, it’s a process of electroplating the entire hole wall with metal, so that the conductive pattern between the inner and outer layers of the double-sided rigid printed circuit board can be electrically interconnected.
A serigrafia aplica-se à impressão de máscaras de solda e impressão de símbolos.
Hot Air Solder Leveler(HASL), ENIG, and OSP are the most common surface finish of rigid PCB circuit board because of their good electrical
The rigid PCB board has been cycling in the final process of milling, CNC machine follows the PCB board outline gerber to route the PCB circuit outline.
The last step of rigid PCB manufacture is open/short circuit test to ensure the quality of the rigid PCB board.
General samples and small batches of rigid PCB circuit boards are tested with flying probes, which can reduce the cost of making test frames, then shorten the delivery cycle. The mass-production rigid PCB boards are tested by test tooling.
Good rigid PCBs boards are vacuum packaged and prepare for shipment.
Below is the basic production process of China Rigid PCB factory.
Following Standard inspection procedure to do material incoming inspection, like copper clad laminate, solder mask oil, etc.
Process control is a very important part of rigid PCB fabrication.KingSun follows standard production processes and strictly controls each process. Especially for key links, detailed records and monitoring should be carried out in order to solve problems in the production process.
After the production is completed, it needs to go through a series of inspection and acceptance links, which is also an important measure to ensure high quality rigid PCB.
Before the product is shipped, an inspection is carried out to ensure that the shipped product meets the customer’s quality requirements. Only products that pass the inspection can be shipped.
Rigid PCB is the physical carrier of design content in the development of electronic products. All circuit board design intentions and product functions are finally realized through PCB boards.
Industrial control rigid PCB circuit boards are classified as special and general-purpose circuit boards.The input and output ports reserved on the circuit board are connected to the user’s own equipment, such as motors, solenoid valves, sensors, to complete the functions.
Medical rigid PCB applications are evolving as rapidly as the medical device industry itself.Some of the most common medical PCB applications include: medical monitors, blood glucose monitors, heart rate and blood pressure monitors, etc.
At present, A car involved more than 100 pieces rigid PCB circuit boards. Touch screens, GPS positioning systems, cameras, all use PCB circuit boards.Various operation control, safety control, and peripheral control functions in ADAS need to be realized through rigid PCB circuit boards
Rigid PCB board is a circuit board made of hard materials such as glass fiber reinforced resin.
Rigid PCB materials include phenolic paper laminate, epoxy paper laminate, polyester glass felt laminate and epoxy glass cloth laminate.
Flex PCB board is a flexible circuit board made of polyimide and polyester material, etc. The typical feature of the flexible board is the insulating film, and the flexible board uses a thin and soft insulating film to achieve insulation and mechanical strength.
Rigid PCB design is to realize the integration of the circuit by laying out the electronic components on the circuit board, thereby improving the performance of the circuit, reducing failure and maintenance costs.
Flexible PCB circuit boards are designed to meet the needs of specific application scenarios, such as space-limited electronic devices that need to be bent, folded, or bent.
Rigid PCB is often used in applications that need to be stronger, such as inside computers or in some mechanical and industrial products.
The electrical performance of the rigid PCB board is more stable and reliable, and it is not easy to be deformed or damaged. They will not affect their performance due to changes in the environment and can be more suitable for high-density wiring.
Placas PCB flexíveis são frequentemente usadas em aplicações que exigem flexão e flexão, como em alguns equipamentos eletrônicos leves e de alta precisão, relógios, carrocerias de automóveis, etc.
Rigid PCB board has the characteristics of firmness, wear resistance, high temperature resistance, etc., and has good thermal performance, which can evenly distribute the heat generation of components.
multilayer rigid PCB can connect multiple circuits together, effectively reducing space and making the originally complicated circuits more compact.
FPC PCB board has higher flexibility, adaptability and can assemble electronic components in more complex shapes.
In addition, FPC circuit board also has the advantages of being lightweight, small size and high reliability, so it is widely used in mobile devices, wireless communications, medical equipment, automotive electronics and other fields.
We can make quick turn FR4 rigid PCB prototype with a very fast turnaround lead time.
PCB prototypes can be quickly produced for PCB board circuit testing and verification in the early stage of product development, improving the efficiency of product development, thereby shortening the project cycle. Below is the quick turn rigid PCB lead time:
| Contagem de camadas | Prazo de entrega padrão | Volta rápida |
| PCB de 1-2 camadas | 4-5 DIA | 24 horas |
| PWB de 4 camadas | 5-6 DIA | 48 horas |
| PWB de 6 camadas | 7-8 DIA | 96 horas |
| PWB de 8 camadas | 9-10 DIA | 140 horas |
| PWB de 10 camadas | 10-12 DIA | 192 horas |
Fazemos circuitos PCB rígidos muito complexos e especiais, como abaixo:
